Skip to content
Home » JBL Flip 3 Power Button Not Working [Solved]

JBL Flip 3 Power Button Not Working [Solved]

How to Fix Your JBL Flip 3 Power Button Not Working?

 If you have a JBL Flip 3 Power Button Not Working, you can fix it yourself by following these steps.

 This post describes how to fix a JBL Flip 3 Power Button Not Working problem, and how to troubleshoot a JBL Flip 3 Power Button Not Working problem.

Let’s see How to Fix JBL Flip 3 Power Button Not Working 

1. JBL Flip 3 Power Button Not Working Solved

2. Reset Your JBL Flip 3

3. Connect the Charger

4. Lose the Grill or Screws

5. Check Your Battery

6. Examine the Connection Cable

7. Fix the Surrounding Buttons

JBL Flip 3 Power Button Not Working 

JBL Flip 3 Power Button Not Working – If you have a JBL Flip 3 then it is quite likely that you will have problems with the power button. In fact, it has been found that some of the JBL Flip 3 units don’t have working power buttons. The article explains why this happens and what you can do to fix it.

Reset Your JBL Flip 3

When a speaker is in trouble, it may be a sign that something is wrong with the device. It is therefore important to have the device checked by a professional.

Turning on your JBL Flip 3 is like waking up in the morning. You have to wait for the speaker to warm up before you can use it.

Connect the Charger

I’m a big fan of JBL. I’ve used their products for years and have always been satisfied. This is a simple way to resolve an issue with your Flip 3 speaker. It might also work for other JBL speakers.

Lose the Grill or Screws

1. If your JBL Flip 3 still does not work, there are a few things you can try to fix it:

2. Turn the volume control down on your device.

3. Press the power button. If the screen is on, turn the volume up. If the screen is off, press the power button again.

4. Power off and on your device.

5. Reset your device.

The power button is located on the front of the phone. It is usually covered with a metal grill that can get stuck when you accidentally touch it. The problem with this is that you cannot reach it without taking off the battery cover. The solution is to loosen the screws around the grill and remove them. This will help to release the pressure on the power button and allow you to use it again.

 Check Your Battery

The best way to check if your battery is damaged is to take it out from your device and plug it into a charger. If you see the power button working, then it is safe to use. However, if you don’t see it working, then it is best to get a new one.

If you need to charge your JBL Flip 3, you should use a JBL Flip 3 wall charger. You can use a universal charger to charge the battery, but it might not work properly. Also, don’t forget to remove the charger from the power source once the battery is fully charged.

If you leave your speaker on when you are not using it, it will generate heat and this will make the speaker warm. This is especially true if you are using it for a long time.

Examine the Connection Cable

If you see that the cable is loose or damaged, then you should get it fixed immediately. You can also try using an alternative cable from the factory.

If your cable is slipping out of the gripper, try to fix it by using a small screwdriver and tightening the screw. Do not use the cable on the computer, because it can damage the USB port.

Fix the Surrounding Buttons

To fix it, you have to remove the rubber cover. Then, you have to pull out the PCB from the outer cover. You can use a screwdriver or a flat head screwdriver. After that, you have to remove the small metal plate with the screws. Remove the screws and the rubber cover from the PCB. Finally, insert the new Bluetooth button into the hole and reattach the cover.

The power button of the keyboard is located on the top right side. If the gap between the two nose-like buttons is too big, then they get stuck with each other and this causes the keyboard to stop working.

When you put a device on a table, it’s normal to have some space between the device and the table. This is the same for your Bluetooth headphones. If you have a Bluetooth device, you should always be careful to place the device somewhere where it won’t be hit by things or damaged.


JBL Flip 3 Power Button Not Working Solved

In conclusion, I found that the problem was caused by the power button. When I took it apart, I found that the part that moves when the power button is pressed had become worn out. I replaced the part, and now the power button works perfectly again.


What can I do if the power button on my JBL Flip 3 doesn’t work?

First, turn off the speaker. Then, turn the speaker on again and try turning the volume up and down.

How do I turn on the JBL Flip 3?

First, you need to turn on the power button. To do this, you need to press and hold the power button for 10 seconds.

What if the power button doesn’t work?

If the power button is not working, you can still use the device.

What if the battery is dead?

The battery is only good for about 6 months. If the battery is dead, you will have to buy a new unit.

How to Start JBL Flip 3?

Power on JBL Flip 3. Hold down both volume buttons for several seconds until LED turns off and then turns off. You may also power it off by holding down the power button and then turning it back on. Once you’ve shut off Flip 3, hold down the power button and turn it on again to start it up.

Leave a Reply

Your email address will not be published. Required fields are marked *